Some Tips To Select The Right Crane

some tips to select the right crane

These valuable tips will help you select the right crane for your project

Cranes have been used by humans for a long time. Now, work in almost any industry is impossible without cranes. If you have a project that would require the use of a crane, you need to research about what kind of crane would serve the purpose.

The information that you require would be related to the proper load rating of the crane, the type of ground where the crane has to operate and other factors. You would need all of that information before reaching a decision on which crane to use.

Crane tips has brought numerous knowledgeable articles for its readers and it keeps providing quality information. This article presented here is in the form of a series of questions and answers that would help you reach the right decision about your crane.

Read the complete article to learn how to select the right crane!

The questions and answers related to the topic are presented below:

How High is the Work to Be Done?

The height of the work is going to impact how the boom is set up, as well as what kind of boom will be necessary. Furthermore, the extension of the crane’s boom can be affected by the wind, which increases exponentially as the height increases. In addition, the amount of counterweight needed to heft loads to ever-increasing heights needs to be calculated differently versus if the height is lower. Tower cranes now have dramatically higher capacity than they once did, and they can often lift over 1,000 meters into the air.

What Material and Condition is the Ground Beneath the Crane?

Cranes need a solid support structure beneath them to support the load and to keep their movement stabilized. While truck mounted cranes are often used when there is concrete to support the crane itself, outriggers are sometimes not enough on unstable terrain. Rough terrain cranes offer the necessary mobility for grass or dirt surfaces without compromising most of the strength. When there is an uneven substrate, you need to consider the width of the crane’s base.

What Kinds of Obstacles are There?

In many environments, especially urban and suburban ones, cranes need to be adapted to circumventing obstacles. In addition to winds, there may be power lines, other buildings and other obstacles that can keep a crane from being able to simply raise the load directly from its origin point to its destination. In some instances, even the control scheme the crane uses can be difficult in the presence of obstacles, with pendant station cables getting caught. Radio controls may be more effective and less potentially hazardous.

How May the Crane Affect the General Public?

Just like how tower cranes are affected heavily by windy weather, the public in the area the crane is operating may be affected by this operation. If the crane’s size impacts the flow of traffic beyond a reasonable threshold, this can cause problems for the entire construction site. Further, if the crane is likely to cause issues with the operation of nearby buildings, this needs to be taken into consideration prior to selecting the type of crane you are going to use for your project.

To learn more about picking the right crane, read the full article on tips how to select the right crane!

Tips To Handle Construction Risk

Some tips to handle construction risk

Some handy tips to help you handle construction risk

Construction has always been a very prolific field. It has continued to be an ever-green field with numerous jobs for people with different backgrounds.  In addition to being a great field, construction also has certain risks that other fields do not have. In fact, it may not be wrong to say that construction is one of the riskiest fields out there.

Crane Tips is all about cranes and construction. We deeply care about our valuable readers and that is the reason we share great information with all of you on a regular basis.

As stated above, construction is indeed a difficult and risky field but the risks in construction can be handled and lowered by employing some tips and following certain strategies.

The strategies to manage the risks in construction are presented here so that you can handle the project in a safe and wise manner.

Do not miss out the golden tips to manage construction risk by reading the complete article!

Allocate Risk

The contract negotiation and preparation phase is the best time for all project leaders, including the owner, contractors, architects, and building manager, to come together and anticipate all potential risks and assign the responsibility of those risks to parties most apt to handle them should the unwanted arise. For example, the building owner and architect should be charged with ensuring design and environment issues are worked out and should draft a plan in case something arises. Meanwhile, contractors should be charged with ensuring personnel are equipped with all the necessary safety guidelines and understand how best to maneuver the environment with equipment in a safe and secure manner.

Managing Funding Risks and Feasibility Risks

These two types of risks are commonly described as “invisible risks” as they are rarely apparent until they are, in which they change the entire game. Yet, with careful preparation and research, most undertaking construction tasks can avoid them.

The first, feasibility risks, arise most commonly out of environmental issues that were not fully addressed in the original plan proposal. They include things like:

  • Extreme weather-based delays
  • Unforeseen factors of a specific location
  • New issues with coding and zoning laws

The ‘Management’ in Risk Management

Finally, it is important to note that this article is entitled with “managing construction risks” because the critical lesson here is not how to avoid all unwanted occupancies, but how to cope with the inevitable. Here, your research, prepare and assign. Understand all of the potential issues with a construction project, consult with the available experts and professionals, set aside budgets to deal with funding risks, and ensure you have the right insurance in place before signing contracts.

Learn more about this important topic by reading the complete guide on managing construction risk.

Some Things You Must Learn Before Buying LED Light Bars

You must learn these before buying LED light bars

These are a few things you must learn before buying LED light bars

A good lighting is very important if you have a factory or facility where works need to be done uninterrupted day and night. The best solution in such a case is to opt for LED light bars. Similarly, if you have the soul of an adventurer and you want to explore and roam around the terrain in your ATV, 4×4 vehicle or motorcycle, then LED driving lights are your best bet. The reason behind using LED light bars and driving lights is simple; they are absolutely the best solution available in the market. Crane Tips has always been concerned with the safety of its readers, especially those in the construction sector or crane business. We have always provided great quality content to our valuable readers and that is the reason we have also selected this particular article which explains a few things that one needs to know before buying LED light bars. Interested in getting the perfect lighting solution? You need to read the complete article to learn more!

Lumens, not watts

Forget what you know about incandescent lamps — your watts are no good here. When shopping for bulbs, you’re probably accustomed to looking for watts, an indication of how bright the bulb will be. The brightness of LEDs, however, is determined a little differently. Contrary to common belief, wattage isn’t an indication of brightness, but a measurement of how much energy the bulb draws. For incandescent lamps, there is an accepted correlation between the watts drawn and the brightness, but for LEDs, watts aren’t a great predictor of how bright the bulb will be. (The point, after all, is that they draw less energy.)

You’ll pay more for an LED light bar

LED light bars are like hybrid cars: cheaper to operate but pricey upfront. When switching to LED light bars, don’t expect to save buckets of cash. Instead, think of it as an investment. Luckily, competition has increased and LED light bars have come down in price but you should still expect to pay much more than an incandescent light. Eventually, the LED light bars will pay off, and in the meantime, you’ll enjoy less heat production and longer lifespan. You need to read the full article explaining the things you need to know before getting LED light bars, in order to learn more about this topic,

Hand Signal Guide For Crane Operators and Crew

Hand signal guide for crane operators

This hand signal guide is for crane operators to work safely

Crane operators must be very skilled and need to be trained properly so that they can perform their jobs efficiently and safely. While working on any site, the operators also require some assistance from the crew or workers present on the site.

The work sites are usually bustling with life, energy and activity during a project and are often so noisy that you cannot communicate easily. People use radio sets or walkie talkies to reach out to each other in such places.

Crane operators are professionals who are entrusted with the loading, movement and carrying of various heavy objects as a part of their daily activities. It is very important to guide the operators during the crane operation to ensure there are no accidents.

We ensure to keep providing you good tips for crane operation and so we have taken a wonderful and important article from TNT Crane & Rigging so that you can get benefited by this valuable information.

The crew or workers must use their hand signals to guide the operators to ensure safety during the process. This article is comprised of definitions and explanations of different hand signals that can be used in order to help the crane operators.

Read the complete article to learn more about this important topic!

Here are the different hand signals used for crane operation, along with their explanations:

Use Main Hoist

There are going to be occasions when the main hoist is necessary for its greater strength. In these instances, the signaler cocks their right arm outward and bends their elbow outward, which allows the signaler to tap on their hard hat with their closed hand as if they were knocking on a door.

Use Whip Line

On some occasions, the whip line or fast line may be preferable to the main hoist. To signal using the whip line, the signaler places his/her left arm horizontally across the front of the body, palm upward. The signaler then makes a forward-facing fist with the right hand and puts the right elbow into his/her left palm in front of themselves.

Raise Boom

To raise the boom, the signaler begins with the right arm outstretched to the side. From there, the signaler points the thumb upward.

Lower Boom

To lower the boom is the reversal of the signal to raise the boom. The signaler begins with the right arm outstretched to the side. From there, they point their thumb downwards.

Swing

It can be necessary to turn or swing the crane. In these instances, the signaler extends the right arm straight outward to the side, with the palm facing downward.

Extend Boom

The boom or primary arm of the crane must sometimes be extended for its reach. In some cases, the boom can be extended independently of lowering or raising it. When the boom must be extended, the signaler places his/her closed hands on either side of their body at hip height, with both thumbs facing outward.

Retract Boom

Retracting the boom can often exert greater leverage with better stability than when the boom is extended. When the boom must be retracted, the signaler places their closed hands at around waist height, with thumbs pointing inward toward their body.

Common Overhead Crane Hazards and Their Prevention

common overhead crane hazards and their prevention

Overhead Crane Hazards Along With Their Prevention

Cranes are fascinating machines and are essential for almost every kind of industry. Without cranes, it is impossible to work efficiently. Overhead cranes are used primarily used in production units or manufacturing industry. There are some dangers associated with overhead cranes. This piece of writing is focused on explaining the dangers and the ways to prevent them.

Read the complete article to learn more about overhead crane hazards and their prevention!

Some Common Overhead Crane Hazards and Tips On How to Prevent Them

Preventing Overhead Crane Hazards: In any type of industry, the coming together of anticipation and pro-actively handling problems is something, which does result in greater success than just reactively responding to incidents. If an individual works in the world of construction and manufacturing, there are hazards always present at job sites, but with proper training and preparation ahead for them, a lot of issues can be prevented.

Potential Electrical Hazards

About 50% of all crane accidents that happen overhead can be attributed to machinery coming into contact with a power source of some kind during operation. Typically, why this occurs is because, as a crane moves materials close to or beneath energized power lines, the hoist line or boom gets into contact with the electrical source. This is an issue, which is about half of all hazards that are associated with these overhead cranes, and it can be stopped with good safety planning.

In addition to this, make sure to ask electrical companies to de-energize or to ground any existing power lines when there are individuals working in close proximity to them. However, until specifically informed by the electrical company, all operators should assume that all power lines are energized and extremely dangerous. A final preventative measure is to make sure all ladders, tools, and other systems being used on the work site aren’t at all conductive.

Any Materials Falling

One of the best ways to lessen the chance of any materials falling down from cranes is clear. It is to make sure to perform regular maintenance of hoists. An example of this is to do load testing maintenance to ensure that you know how many pounds a hoist can handle exactly.

Here at Crane Tips, we always make sure to put safety and prevention first. It is our number one priority. Because of this fact, we ensure that all the machines we have are kept well maintained and up to date. What this does is ensures that you will be getting the most effective, as well as, the most reliable equipment that is available. Please view the equipment that we have on hand for sale or rental today. It may help you to find the crane that you require for your next major project coming up.

Erosion Control on Steep Slopes and Embankments

How to control erosion control on steep slopes

Heavy rain can cause damage to the soil and it can lead to erosion as well. Erosion is the action of surface processes that remove soil, rock or other dissolved material from the surface of earth. The removed particles are then transported to other locations.

Some problems associated with erosion

Erosion can cause a lot of problems. When the erosion process starts, the top soil generally erodes first. The top soil is rich in nutrients and when it erodes away, the remainder of the soil does not have enough nutrients to support plant life.

In addition to the removal of top soil, erosion can cause an increased runoff. The reason behind this is that, as the top soil erodes away, the soil that is left behind, does not have good water retaining capability. Due to the erosion of top soil, the organic matter in the soil is reduced and so water retention is decreased.

Erosion on soil can also cause sediment to accumulate in nearby lakes, oceans and rivers. Due to the sedimentation, the fish and other wildlife find it difficult to see well and find their food. Another problem that may arise is that they sometimes intake soil particulates through their gills which affects their breathing.

Due to land development on hilly areas, erosion control becomes vital on steep slopes and embankments. Especially in areas that experience heavy rainfall. Such steep slopes that have no vegetation or cover are more likely to develop erosion as compared to other ones. Erosion can cause a lot of damage to the landscape and the infrastructure that is surrounding a particular project. So, it is essential to protect the hillside from erosion before the starting and completion of the project.

Read the complete article to develop an understanding of this problem and to learn how to cater this problem!

Soil erosion is bad and can prove to be very harmful, so it must be controlled. There are many ways to control and limit this issue and are described below:

Natural Solutions

natural solution to control erosion

The most effective, natural way to control soil erosion on steep slopes and embankments is to plant vegetation. Not only will the grass, fescue and leaves help to slow down raindrops as they fall, the roots of the plants will also help to hold the soil together, making it harder for water to wash it away.

However, when planting vegetation on a slope to stop erosion, you need to keep in mind that what you’re planting is just as important as the planting. Though grasses can create a groundcover that can absorb some moisture, they have less effective storm water filtration ability compared to native ground cover.

Artificial Solutions

artificial solutions to control erosion

Other than planting vegetation, there are also a variety of artificial solutions you can use. For instance, the use of geomats has become popular over the last few years. Geomats are water permeable polymers that are used to help fix soil elements, grass and small plant roots, and have been shown to work extremely well, especially on barren slopes that have no vegetation.

Soil Composition Enhancement

soil composition enhancement

You could also control erosion by controlling the soil itself. As heavy rain tends to be the biggest culprit for soil erosion on slopes and embankments, by controlling the composition of the soil, you specialty soils could control the effect that water has on it and therefore the likelihood that it will be eroded.

The complete article can be accessed here.

TNT Crane Opens A New Branch In Edmonton Alberta

TNT Crane & Rigging Canada Inc. opens new Branch in Edmonton, Alberta

TNT Crane & Rigging Canada is pleased to announce that it will open a branch office outside of Edmonton in Leduc, Alberta in July, 2016. The new branch will be located at 3310 Allard Avenue, Leduc, Alberta.

TNT is expanding into the area to provide crane services to existing and new customers in the region.  TNT crane services currently have seven branches stretching from British Columbia to Ontario servicing multiple industries including Oil & Gas, Wind Construction, Bridge & Road Construction as well as Commercial customers.

Bob Fairbank, President & CEO said “We are excited about opening our newest branch in Edmonton and bringing our experience and expertise to better serve our customers in the region. Edmonton offers great potential for growth and we look forward to expanding our customer base here through this commitment.